Von Duprin SO12VAC N/A Kit Exit Device

Von Duprin SO12VAC N/A Kit Exit Device Reviews

Other Picture

12 Volt Rectifier Kit for Von Duprin Electronic Exit DevicesConvert the electrical output your new Von Duprin exit device with ease with this 12 volt rectifier kit for all of Von Duprin s electronic exit devices. This kit will allow you to convert AC current to the DC current required to run Von Duprin s electric strikes, latches and devices.Over the years, Von Duprin has been an innovator in many new concepts to the industry. Currently, Von Duprin manufactures the widest range of exit devices and outside trim operations, all designed to meet the needs of architects and building owners. Field installableIncludes plug in-line to solenoidConverts AC voltage to operate the DC solenoids

Visit Store Now !!

Detail Products

Detail Reviews

May 01, 2011 06:20:04

Kreg SML-C125 1-1/4-Inch No. 2 Coarse Screw (1000-Pack)

Kreg SML-C125 1-1/4-Inch No. 2 Coarse Screw (1000-Pack) Reviews

Other Picture

Kreg SML-C125 1-1/4-Inch No. 2 Coarse Screw (1000-Pack) Feature

• 1,000-pack of softwood to softwood #8 coarse screws
• Designed for pocket-hole joinery
• Self-tapping auger point eliminates pre-drilling
• Casehardened, steel coated and dri-lube finished for easier driving
• Large-thread diameter for greater holding power

Kreg's self-tapping screws were designed for its famous pocket-hole joinery, but that's not all they're good for. Kreg's self-tapping auger point eliminates time-consuming pre-drilling, and these screws are made from the highest quality steel, case-hardened and coated with a dri-lube finish. That means less driving torque for you. This coarse-thread screw has a larger thread diameter and provides greater holding power when driving a screw into soft material such as plywood, particle board, MDF, melamine and pine. The washer head offers a great surface area to seat the screw firmly and helps prevent overdriving. They're on the spendy side, but the quality is worth it.--Kris Jensen-Van Heste

Visit Store Now !!

Detail Products

• Kreg SML-F125-1000 1 1/4-Inch No. 7 Fine Pocket Hole Screws with Washer-Head, 1000-Pack
• Kreg DDS 3-Inch No.2 Square Driver Bit and 6-Inch No.2 Square Driver Bit for Kreg Pocket Hole Systems
• Kreg KHC-RAC Right Angle Clamp
• Kreg K4MS Jig Master System
• Kreg SML-C250B-250 Blue-Kote Weather Resistant Pocket Hole Screws - 2 1/2", #8 Coarse, Washer Head, 250 count

Detail Reviews

Apr 30, 2011 11:19:04

Rockler JIG IT Game-Drilling System for Tic-Tac-Toe/Last Man - for pegs

Rockler JIG IT Game-Drilling System for Tic-Tac-Toe/Last Man - for pegs Reviews

Other Picture

Our templates let you drill 100 holes or more in minutes, making it easier than ever to create lots of games quickly, accurately, and with excellent repeatability! Durable 1/4" Plexiglas templates for making game boards, great for making gifts in larger quantities. Templates measure 4-1/2" x 4-1/2". Sets include drilling jig and line template.

Choose the template, then select the appropriate drill bit. Our exclusive bit for marble games (Rockler# 41463, sold separately) cuts a clean, perfect recess that keeps the marbles in place. Seal your board and then use the paint markers (Rockler# 41050, sold separately) and line templates to add decorative touches. Line templates are precisely cut for creating evenly spaced lines. Markers contain black paint for crisp, solid lines.

Visit Store Now !!

Detail Products

Detail Reviews

Apr 29, 2011 15:56:03

Kreg DK3100 1-1/2 Horsepower Floor Electric Fully-Automatic 3-Spindle Pocket Machine

Kreg DK3100 1-1/2 Horsepower Floor Electric Fully-Automatic 3-Spindle Pocket Machine Reviews

Other Picture

Kreg DK3100 1-1/2 Horsepower Floor Electric Fully-Automatic 3-Spindle Pocket Machine Feature

• Three spindle design
• Fixed spacings of 3/4", 1" and 1-3/4"
• Electric, 1-1/2 hp motor
• 110V single phase 90 psi for hold down
• Includes 2 DKDB and 1-LH-DKDB 3/8" cobalt step bit

Drills two pocket holes in one machine cycle. 3/4-Inch, 1-Inch and 1-3/4-Inch on-center spacings. Fast, 1 second cycle time. Quiet and powerful. The H6828 is the only pocket hole machine on the market that has the ability to drill two pocket holes in one machine cycle across rails of varying widths. Drill spindles in the machine are fixed at 3/4-Inch, 1-Inch and 1-3/4-Inch on center allowing it to drill today's most common rail widths of 1-1/2-Inch up to 3-3/4-Inch in one machine cycle. Three step drill bits are utilized in the machine, one of which is left-handed.

Visit Store Now !!

Detail Products

Detail Reviews

Apr 28, 2011 17:43:04

Replacement Finger - Right

Replacement Finger - Right Reviews

Other Picture

Replacement finger for Leigh dovetail jig.

Visit Store Now !!

Detail Products

Detail Reviews

Apr 27, 2011 22:00:03

Kreg SML-C250 - 2000 Pocket Screws 2 1/2-Inch, #8 Coarse, Washer Head, 2000 Count

Kreg SML-C250 - 2000 Pocket Screws 2 1/2-Inch, #8 Coarse, Washer Head, 2000 Count Reviews

Other Picture

Kreg SML-C250 - 2000 Pocket Screws 2 1/2-Inch, #8 Coarse, Washer Head, 2000 Count Feature

• 2-1/2" screw for joining 1-1/2" stock
• Maxi-Loc washer head
• Great for softer materials like pine, plywood, particle board, MDF and melamine
• Larger threads provide maximum holding power
• Washer head seats flushly in the bottom of the pocket, eliminating pull through

2 1 2" Coarse Thread self tapping screws are specially designed for pocket hole joinery. They feature a self tapping auger point that eliminates pre drilling and a flat head that seats flushly in the bottom of the pocket hole. All of our screws utilize a

Visit Store Now !!

Detail Products

• Kreg KHC-RAC Right Angle Clamp
• Kreg SML-C125 1-1/4-Inch No. 2 Coarse Screw (1000-Pack)
• Kreg KHC-90DCC 90-degree Corner Clamp
• Kreg NZ03 Magnetic Drawer Slide Mounting Tool
• Kreg SML-C125-5000 1 1/4-Inch Pocket Screws, #8 Coarse, Washer Head, 5000-Pack

Detail Reviews

Apr 27, 2011 02:58:06

Dowelmax Precision Engineered Wood Joinery System

Dowelmax Precision Engineered Wood Joinery System Reviews

Other Picture

Dowelmax Precision Engineered Wood Joinery System Feature

• Simplifies the creation of strong, perfect joints for building furniture
• Save time and increase strength on every joint
• You won't believe the precision
• Highly versatile and adjustable
• Great for the amateur and professional woodworkers

Create strong, accurate wood joints of virtually any configuration and size. Dowelmax joint configurations and sizes can be single, double and triple row, flush, offset, mitre, and face joints, from 1" x 1" to 1" x 12" and from 2" x 2" to 4" x 12". The patented design coupled with rigorously maintained manufacturing tolerances of +/-.001 inch for the 36 aluminum, brass and steel components making up the kit ensures that the Dowelmax is accurate and repeatable from workpiece to workpiece and through any adjustment. The Dowelmax Kit is a professional quality, precision engineered joining system that is intended to last a lifetime. The Dowelmax Kit weighs 3.20 lbs and is 3.5" x 3.5" x 2.75". The main body of the jig is polished 6160 aluminum and the drill guide material is carbo-nitride hardened (60 Rockwell @ .015" deep) and black oxide coated steel. All Dowelmax components are manufactured and assembled in North America.

Visit Store Now !!

Detail Products

Detail Reviews

Apr 26, 2011 04:08:04

Kreg Deck Jig System

Kreg Deck Jig System Reviews

Other Picture

The best helper you'll ever have for building decks, fencing and more! This jig guides
you as you drill and drive deck screws at the optimal angle to achieve concealed
fastening of deck boards. No more exposed nails or screws! An easy grip handle and
90 alignment tab make setup extremely easy. The onboard drilling jig is preset at the
optimal angles for straight-on as well as left and right corner fastening. Simply drill
your holes with the included bit and drive the deck screws with the included square
drive bit. Spacer rings are included to ensure uniform, accurate spacing of deck boards.


Additional Features:

Includes the Deck Jig, 6" drill bit, 6" KTX square driver bit, 100 Protec-Kote deck
screws, three 5/16" spacer rings, three 1/4" spacer rings, two stop collars, allen wrench,
instructional DVD and durable carrying case.
For stock from 3/4" to 1-1/8" thick.

Visit Store Now !!

Detail Products

Detail Reviews

Apr 25, 2011 08:51:05

1/2'' BeadLOCK Tenon Stock, 12'' Pieces, 3 Pack

1/2'' BeadLOCK Tenon Stock, 12'' Pieces, 3 Pack Reviews

Other Picture

This unique tenon stock is specially designed for use with the Beadlock Loose Tenon Joinery System (available separately). The flutes on the stock increase the amount of glue surface and also prevent the joint from racking. About the Beadlock System:The Beadlock Joinery System allows you to create joints with mortise and tenon strength without the need for large, expensive machinery. A Beadlock jig and a hand drill are all you need to get started making rock solid, invisible loose tenon joints.

Visit Store Now !!

Detail Products

Detail Reviews

Apr 24, 2011 07:49:04

Kreg DKDBSP4 3/8-Inch Step Twist Drill Bit for Pocket Hole Machines

Kreg DKDBSP4 3/8-Inch Step Twist Drill Bit for Pocket Hole Machines Reviews

Other Picture

Kreg DKDBSP4 3/8-Inch Step Twist Drill Bit for Pocket Hole Machines Feature

• The DKDB bit is made of cobalt steel that increases the bits life.
• Our one-piece design eliminates clogging and provides a much smoother
• Faster drilling stroke than the drill bits with replaceable center drills.
• Because the DKDB bit is also 3/8-Inch diameter it can be used in any of our other manual
• Made in the U.S.A.

Our one-piece design eliminates clogging and provides a much smoother and faster drilling stroke than the drill bits with replaceable center drills. The DKDB bit is made of cobalt steel that increases the bits life. Because the DKDB bit is also 3/8-Inch diameter it can be used in any of our other manual jigs as a premium replacement. Be sure to order the left hand drill bit (LH- DKDB) for the middle spindle of the DK3100 fully-automatic machine. Diameter: 3/8-Inch Count: 1 Tip Diameter: .170-Inch Tip Length: .875-Inch

Visit Store Now !!

Detail Products

Detail Reviews

Apr 23, 2011 12:28:04

EURO-HANDLE-IT

EURO-HANDLE-IT Reviews

Other Picture

EURO-HANDLE-IT Feature

• Install Handles and Knobs Fast and Accurately
• Drill holes of difference centers up to 24" apart and up to 12" from the edge.
• Easy to read english and metric scales are indicated.
• A special V notch allows for diagonal 45 degree installation.
• Jig is made of virtually indestructible polycarbonate plastic.

Drill holes of difference centers up to 24" apart and up to 12" from the edge. Easy to read english and metric scales are indicated. A special V notch allows for diagonal 45 degree installation. Jig is made of virtually indestructible polycarbonate plastic and features hardened steel drill bushings for use with a standard 3/16" drill bit.

Visit Store Now !!

Detail Products

• Pony 8510BP Cabinet Claw (2-Pack)
• Mediabridge Ultra Series - High Speed HDMI Cable With Ethernet - Category 2 Certified - Supports 3D & Audio Return Channel [Latest HDMI Version Available] - (10 Feet)

Detail Reviews

Apr 22, 2011 17:17:35

Ratchet Knob 3/8'' bolt 16 tpi

Ratchet Knob 3/8'' bolt 16 tpi Reviews

Other Picture

Ratchet Knob 3/8'' bolt 16 tpi Feature

• 3/8'' bolt 16 tpi
• Zinc plated steel bolt is 1'' long.
• Features a push button ratchet clutch

Ratchet Lever Knob is perfect when access is limited or makes Star or T-Knobs impractical. Features a push button ratchet clutch. Hold button down and pull up on lever to release clutch. Zinc plated steel bolt is 1'' long.

Visit Store Now !!

Detail Products

Detail Reviews

Apr 21, 2011 12:12:03

Von Duprin 090081 N/A part Exit Device

Von Duprin 090081 N/A part Exit Device Reviews

Other Picture

Wedgetite Screw Package for 55 / 8827 Series Exit DeviceReplace a broken or missing part or complete the installation of your exit device with this end wedgetite screw package for Von Duprin s 55 and 8827 series exit only devices.Over the years, Von Duprin has been an innovator in many new concepts to the industry. Currently, Von Duprin manufactures the widest range of exit devices and outside trim operations, all designed to meet the needs of architects and building owners.Pack of 30Compatible with 55 and 8827 series exit only devices

Visit Store Now !!

Detail Products

Detail Reviews

Apr 20, 2011 13:09:05

Porter Cable 430S0PC Omnijig Joinery System Straight Bit - S0

Porter Cable 430S0PC Omnijig Joinery System Straight Bit - S0 Reviews

Other Picture

Porter Cable 430S0PC Omnijig Joinery System Straight Bit - S0 Feature

• 1 of 4 straight bits used with the omnijig joinery system
• Used to cut miniature box joints
• 9/32-inch cutting diameter
• Flute length 25/32-inch
• Total bit length 3-1/8-inch; Solid carbide, spiral upcut

1 of 4 straight bits used with the Omnijig Joinery System. Used to cut miniature box joints. 9/32" cutting diameter. Flute length 25/32". Total bit length 3-1/8". Solid carbide, spiral upcut. 1/4" Shank.

Visit Store Now !!

Detail Products

Detail Reviews

Apr 19, 2011 14:29:05

OPENS 6" "Gold Series" Self-centering Doweling Jig

OPENS 6" "Gold Series" Self-centering Doweling Jig Reviews

Other Picture

OPENS 6" "Gold Series" Self-centering Doweling Jig Feature

• 3 Times faster from open to close than any other self-centering doweling jig on the market.
• 5 permanent holes 1/4", 5/16", 3/8", 7/16" and 1/2"
• Precision jaws opens a full 6"
• All surfaces coated for rust prevention.
• Patent Pending

Quality and durability has always been associated with the TASK Pro Center USA line of woodworking hand tools. Now accuracy and speed come together in one product. This Patent Pending design will allow you to open and close the precision jaws three times faster than any of our competition. This jig is made from the finest tempered alloy steels and aluminum, coated to ensure durability and rust prevention. Picture shown is actual dowleing jig, bushings sold separately.

Visit Store Now !!

Detail Products

• General Tools 888 1/4-Inch to 1/2-Inch Dowel Center Transfer Plugs
• General Tools S838 6 Piece 3/16-Inch to 1/2-Inch Drill Stop Assortment

Detail Reviews

Apr 18, 2011 16:01:19

Kreg PRS3020 True-FLEX Featherboard - Twin Pack

Kreg PRS3020 True-FLEX Featherboard - Twin Pack Reviews

Other Picture

Kreg PRS3020 True-FLEX Featherboard - Twin Pack Feature

• Comes with wedge-lock hardware which works in t-slots or miter slots on tablesaws, router tables, band saws and more.
• Each finger provides consistent and optimum pressure
• Made of an extremely durable plastic composite body
• 6.9-inches W by 8.7-inches L by 2.09-inches H
• 1.2-pounds

The True-FLEX Featherboard gets its name from the careful engineering that went into its design. Many featherboards on the market today apply too much pressure or not enough pressure to the workpiece, resulting in imperfect cuts and less than safe operation. Each finger of the True-FLEX featherboard is designed to provide a consistent and optimum pressure. The featherboard is made from an extremely durable plastic composite body and includes an exclusive wedge-lock system. Whether youre using a miter-slot or a T-slot, working on a table saw or a router table, the wedge-lock system adjusts accordingly and lets you work with confidence. Contains two featherboards.

Visit Store Now !!

Detail Products

• Kreg PRS3100 Multi-Purpose Router Table Switch
• Kreg KMS7215 Micro-Adjuster for Band Saw and Router Table Fences
• Kreg PRS1040 Precision Router Table System
• MLCS 9167 Safety Push Block and Stick Package, 5-Piece
• Kreg PRS3090 3" Dual Locking Caster-Set (4 Piece)

Detail Reviews

Apr 17, 2011 12:02:07

Five Star Knob with Through-Hole, 5/16'' 18 tpi

Five Star Knob with Through-Hole, 5/16'' 18 tpi Reviews

Other Picture

Three different styles available (sold separately). Each style is available in thread sizes: 1/4''-20, 5/16''-18 and 3/8''-16.

The 2" T knob with Through-Hole (shown left) gives you that little extra torque when you need it. Narrow profile allows better clearance.

The Five Star Knob with Through-Hole (shown center) and insert accommodates bolts of various lengths. Works great with our T-slot system.

The Five Star Knob with 1" Stud (shown right) is the studded version of our most popular knob.

Visit Store Now !!

Detail Products

• 3.5'' x 5/16''-18 thread T-Bolt, 5 Pack
• Five Star Knob with 1'' Stud, 5/16'' 18 tpi

Detail Reviews

Apr 16, 2011 16:46:06